Ping shaft length chart

Ping shaft length chart DEFAULT

Fitting Charts

Custom Built Clubs for Junior Golfers

Club Length – One of the most important aspects of introducing a young player to the game of golf is providing them with proper fitting equipment. Poor fitting clubs can lead to swing problems that can be difficult to correct in later years, and even affect the desire to play.

Clubs that are too long will cause the junior to compensate with a swing that is too “flat”, and clubs that are too short will lead to a swing that is too upright. Both instances will make it difficult for the junior to make consistent contact with the ball, resulting in needless frustration and an understandable desire to give up and try something that is more fun! The best choice is a club approximately 1.5” longer than an exact fit, which allows the junior to “choke down” during initial play, gradually moving his/her hands higher on the grip as they grow over the next two seasons.

You can find the pre-packaged set that matches best by comparing your junior’s measurements with those recommended by the manufacturer. Typically, if the height range for the set is 44 – 52 inches and your junior stands 48 inches tall you would have a great match. If your junior is at the lower end of the scale you may want to continue your search, as the clubs may be be too long. If your junior is at the high end of the range you may want to select the next larger size, or search for a different height range.

Bottom line:
 if your child’s height is about in the middle of the manufacturer’s suggested height range, you’re safe. If not, search for a different height range or consider custom built clubs, which we build about 1.5 – 2″ longer than an exact fit. This allows the junior to grow into the clubs over the next two years and allows parents to maximize their investment.

 

Playing Lengths by Height

HeightDriver3 Wood3 Iron5 Iron7 Iron9 IronPWSWPutter
36″ 26″25″22″21.5″21″20.5″20.5″20.5″
37″26″25″23″22.5″22″21.5″21.5″21.5″
38″26″25″23″22.5″22″21.5″21.5″21.5″
39″27″26″24″23.5″23″22.5″22.5″22″
40″28″27″24″23.5″23″22.5″22.5″22″
41″30″29″26″25″24″23.5″23.5″23″
42″31″30″27″26″25″24.5″24.5″23.5″
43″32″31″27″26″25″24.5″24.5″23.5″
44″33″32″28″27″26″25.5″25.5″24.5″
45″33″32″28″27″26″25.5″25.5″24.5″
46″34″33″29″28″27″26.5″26.5″25.5″
47″34″33″29″28″27″26.5″26.5″25.5″
48″35″34″31″30″29″28″27.5″27.5″27″
49″35″34″31″30″29″28″27.5″27.5″27″
50″36″35″32″31″30″29″28.5″28.5″28″
51″36″35″32″31″30″29″28.5″28.5″28″
52″36″35″32″31″30″29″28.5″28.5″28″
53″37″36″33″32″31″30″29.5″29.5″29″
54″37″36″33″32″31″30″29.5″29.5″29″
55″38″37″34″33″32″31″30.5″30.5″30″
56″38″37″34″33″32″31″30.5″30.5″30″
57″39″38″35″34″33″32″31.5″31.5″31″
58″39″38″35″34″33″32″31.5″31.5″31″
59″39″38″35″34″33″32″31.5″31.5″31″
60″40″39″36″35″34″33″32.5″32.5″32″
61″41″40″37″36″35″34″33.5″33.5″33″
62″41″40″37″36″35″34″33.5″33.5″33″

Club andShaft Weight – Another important aspect of junior golf clubs is the overall club weight. Heavy clubs with cut down adult steel shafts and clubheads designed and weighted for adults are very difficult for smaller golfers to swing efficiently, and sometimes result in the junior golfer spinning around way too many times at the end of the swing!

A club properly weighted for a junior will allow the speed of the arms to match the rotation of the body, resulting in better club head-ball contact, more distance and improved accuracy. We have found that up to about nine years old a junior needs both a lighter club head and a lighter shaft. A lighter shaft combined with standard weight clubheads works great for most nine to twelve year olds, preparing them for graduation to adult clubs in their teen years.

We look far and wide for the perfect match between quality, technology and playability, then test the clubs extensively to make sure our customers will be happy with the performance characteristics.

Shaft Flex – It is very difficult to design a junior shaft that matches the varying swing speeds of juniors. Companies have marketed junior clubs with shafts that were proven to be too flexible, and at the other end of the spectrum Tiger Woods successfully played an extra stiff adult shaft as a kid. Since a shaft which is too flexible does not work well and most junior golfers do not possess the athletic ability of Tiger Woods, something in the middle suits most juniors.

In general, the younger the golfer the more flex required, so we look for specially designed composite shafts in sets for juniors between three and eight years old. For juniors between nine and twelve years old we offer shafts specially designed for juniors (smaller grip diameter, added flex) . We also offer a lightweight, low flex point graphite shaft for those juniors with slower swing speeds or those seeking added distance.


Grips
– Since the grip is where the human body contacts the club, we believe it should be as comfortable as possible, so we use the best grips available.

Sours: https://www.patriotgolf.us/custom-fitting/fitting-charts/

Understanding the Ping Colour Chart & Dot System

Ping Colour Chart – can you understand it?

Are you looking for a new set of Ping golf clubs? Understanding the ping colour chart and colour code system used by Ping will enable you to select a set that best suits your game. Ping’s unique colour code refers to lie angle, which is the angle between the clubs shaft and the sole of the club, in relation to its length. Sounds very technical, but it really isn’t and by checking the chart below you will find out the best club set up for you.

It is so important to make sure you get the best out of your clubs. Buying new golf clubs is a big investment and by custom fitting them correctly, this can improve your shot making and create better scores.

Step One :- Once you have downloaded your Ping Colour Code Chart from Ping.com you can see that you have overall height measurements along the top and wrist to floor measurements down the side. If you want to use a metric scale you need to look at the bottom.60 Day Play Better Promise on Ping Golf Clubs

Step Two :- Firstly you need to see if you suit a longer or shorter shaft. Find your overall height along the top and immediately underneath you will see any alteration if needed. For example, if you are between 5ft 7inches and 6ft 1inch you should be a standard length, but it you are either side of this you will need to have shafts extended or decreased by the measurement recommended.

Step Three :- If you then intersect your overall height with your wrist to floor measurement you will clearly see the colour band that best suits your size. Currently there are 12 colours  ranging from maroon to gold. As a general rule, the taller you are the more upright you will need your clubs, as against the shorter you are the more flatter you will be. Your lie angle measurement is stated under the colour which is also handy to know especially if you already have a custom fit set of clubs from other manufactures and are trying to compare.

Step Four :- If you are bordering between two colour codes, according to Pings website you need to determine whether your ball flight with your iron shots are typically a fade, slice, hook or draw. If you want to reduce your fade or slice then choose a more upright colour code opposed to if you want to reduce your hook or draw then choose a flatter colour.

Here at “The Golf Shop Online” we acknowledge the importance of custom fitting and want to make sure you tailor your specification to your game and swing. We have a page just dedicated to Ping Custom Fit Advice plus an ask the pro service

If you want to discuss any aspects of the Ping colour chart or want to run through your recommendation then please email or call our team of professionals who will be willing to offer advice. Our email address is [email protected] and our phone number is 01626 830537

 

New Ping Colour Code Chart

 

Click here to see our full range of Ping Golf Irons of which all can be custom built to your individual specification.

 

 

 

PingPing Colour Chart

About Andrew Probert

I am the Manager of the GolfShopOnline and have worked in the golf retail industry for over 20 years.

Sours: https://www.thegolfshoponline.co.uk/blog/ping-colour-chart/
  1. Mclaughlin ave san jose
  2. Nina ultra pro lipstick
  3. 1965 in country music

What Do Ping Dot Colors Mean?

What Do Ping Dot Colors Mean?

Ping Golf has made some changes in 2017 along with their G400 line of golf clubs release so please see the update at the bottom of this post.  Updated July 11th, 2017.

Click Here To Read our 2020 Article Revisiting PING’s Dot Colors>

Ping has been the long-standing leader and a huge advocate of getting custom fit for your next set of golf clubs, especially with a new Ping iron set.  If you’re somewhat familiar with Ping irons you’ll notice each iron set has its own Ping Dot Color stamped on the hosel or cavity of the iron.  So what exactly do these Ping dot colors mean and how will they matter to me if I were to get custom fit for a new set of Ping irons?

Ping has a total of 12 dot colors and each one is different based on each golfer’s necessary lie angle of their irons as well as the shaft length.  Lie angles range from 3.75 degrees flat to 4.5 degrees upright in 0.75 degree increments.  Each set of irons is stamped with a dot color that signifies its lie angle and shaft length and while this doesn’t have anything to do with the specific iron set model, it only has to do with each model of irons that Ping brings to the market. So each specific set of Ping iron has 12 different dot colors.

From flat to upright the dot colors go in the following order with gold being the flattest lie angle at 3.75 degrees to brown, orange, purple, red, black, blue, yellow, green, white, silver, and maroon being the most upright at 4.5 degrees.  Please refer to the chart below for more exact specifications regarding each dot color’s lie and shaft length.  For decades Ping has deemed the black dot iron set at being the standard lie angle that most golfers fit into and if you purchased a Ping iron set off the rack from any golf retailer several years ago, in most cases it would’ve been a black dot iron set.

However, sometime between mid-2015 and 2017, after doing further research Ping has discovered that more golfers fit into a bit more of an upright lie angle and now blue dot or yellow dot iron sets have become the new Ping standard dot color, and are typically what more golf retailers keep in stock as opposed to only black dot Ping iron sets.  Keep in mind this does not mean that the lie angles have changed but it’s just that Ping has found that their blue or yellow dot lie angles fit more golfers’ swings than black dot iron sets.

Ping G Iron Set Yellow Dot

Getting custom fit for a set of irons requires several different factors, but for the sake of keeping things simple regarding Ping Iron Set Dot Colors, the main factors in getting fit correctly are your height, and more importantly the length of your wrist to the floor.  The other important factor is the lie angle of your iron set.  While some inexperienced golf custom fitters only measure the first two factors of your height and the length of your wrists to the floor, it is most important to measure your lie angle.

To accurately get custom fit into the correct lie angle, it’s best to actually hit several golf shots off of a lie board.  What does this involve?  It’s actually a fairly easy process, especially if you have a pretty consistent golf swing.  A certified custom fitter will put down a plastic lie board along with some impact tape on the bottom sole of your iron and ask you to take several swings.  You’ll end up the marking the impact tape on the bottom of the iron and your custom fitter will be able to adjust your Ping dot color accordingly, either more upright or more flat so that the sole of the club is striking the lie board and marking the impact tape exactly in the middle.

Ping Dot Color Lie Angle Board

On a side note, to get fit for your lie angle correctly, its important that the person fitting you puts the impact tape on the bottom of the club correctly, Ping provides this impact tape, and your custom fitter should know how to match up the appropriate lines on the impact tape with the grooves on the club face so you get an accurate reading. If the impact tape is put on recklessly you could get fit with an incorrect dot color.

Why is it important to hit real shots off of a lie board?  If you strike the lie board and mark the tape too far towards the toe of the sole, that will cause your iron to open as you strike the ball through the turf and causing a slice or push to the right.  And the opposite is the case when you mark the impact tape more towards the heel.  That will cause you to pull the golf ball to the left, causing an unwanted draw or hook.  Some fitters or golfers think that you can tell if your lie angle is correct by just looking at your setup, this would be referred to as a static fitting, whereas a dynamic fitting would be to truly measure your lie angle during impact and not your setup as the two are often quite different.  Most golfers typically strike the golf ball at a more upright lie angle through impact as opposed to if they were measured only at the setup position.

What happens if you’ve already purchased an expensive set of brand new Ping irons only to find out that you’ve been inaccurately custom fit?  Luckily, you do have a couple options, if you’re lie angle isn’t too far off, say less than 2-3 degrees you can go to your local golf store or golf club repair shop and with the use of a golf club bending machine your irons can be adjusted and bent to the correct lie angle.  If your shaft length is too long or short that can also be fixed quite easily as golf iron sets can be cut down or extended up to 2 inches.

Ping Dot Color Chart

The ideal Ping dot color will help you to make sure you get the correct lie angle and shaft length that is perfectly custom fit for your golf swing so that when you take your swing the sole of the iron is perfectly parallel to the ground creating true, crisp iron shots in the center of the clubface.  Getting fit by a certified Ping Custom Fitting Specialist and getting a new Ping iron set that truly fits your own unique golf swing ultimately generates straighter, longer, and more consistent ball striking in the center of the club face, which also aids in a more consistent trajectory leading to perfect distance control.  This is what Ping Golf is known for and is the exact reason that golfers, who play Ping iron sets, ONLY play Ping iron sets and just upgrade from time to time to the newest model.

Learn more about Ping Custom Fitting Here.

UPDATE: July 11th, 2017

2017 New Ping Color Code Chart

Below you will find a video explaining the changes to Ping’s new 2017 color code chart as well as an image of the chart and Ping’s FAQ’s regarding the new chart.

2017 New Ping Color Code Chart

New PING Color Code Chart Change FAQs

  • What is the reason for this color code change?
    • PING and its iconic Color Code Chart set the standard for custom-fitting systems nearly 50 years ago and it continues to be the method of choice for club fitters around the world. Through decades of fittings and research, PING has evolved the Color Code Chart with the goal of delivering the most accurate and comprehensive iron fittings in golf.

The updated Ping Color Code Chart will allow the fitter to deliver a more accurate fit, especially at the extremes of height and wrist-to-floor measurements. By removing the length-lie dependency, fitters no longer need to convert color codes when adding or removing shaft length.

  • What has changed?
    • The length-lie dependency has been removed by changing color code bands to an “S-shape”.
    • Each color code has a fixed lie angle irrespective of club length. This removes the need for converting color codes when using non-standard-length clubs with the AFS system.
    • Color codes have moved to 1° increments to simplify lie-angle offerings.
    • Yellow and Purple color codes have been removed.
    • Updated length recommendations better align static recommendations with dynamic fitting results. Height columns are now scaled for easier use and overlaps are removed.
  • How is it more precise?
    • By analyzing over 20,000 fittings from our nFlight database, combined with years of research, we have made data-driven changes to better align static and dynamic fittings, particularly with respect to players’ length recommendations.
    • 75% of players will fit to a dynamic color code within one of the new static recommendation compared to 70% previously, while 95% will fit within two color codes compared to 90% on the previous color code system.
  • How is it simpler?
    • Removing the length-lie dependency eliminates the need to convert color codes when building AFS heads at over/under standard length.
    • It also removes the need to convert back when ordering clubs at over/under standard length after a fitting using our AFS system.
    • Removing height overlaps and scaling eliminates ambiguity.
    • Plotting height and wrist-to-floor measurements for a static recommendation is more intuitive.
  • Why do I need to fit length before color code now?
    • Previously, with the length-lie dependency, PING would adjust lie angle for the color code depending on the length of the club when ordering.
    • However, by removing the length-lie dependency to simplify the building of AFS clubs and the ordering process, PING no longer does this conversion. This means that if the length changes, the color code will likely need to change too.
  • Can a golfer order a new set based off their previous specs?
    • New set orders can be placed only on the new color code system. PING always recommends being fit. However, using the conversion chart we can calculate the new color code based off a previous set. The actual lie angle of the clubs will be almost identical, even though the color code may be different. There will be no difference in the performance of the clubs. This applies to all models on new orders.
  • Can a player’s old set be moved on to the new color code system? Can a player’s new set be moved on to the old color code system?
    • No, all sets must remain on the same color code system they are built on. If the set was built on the previous system, it must remain on that system.
  • If a player loses a club or wants to repair/replace/fill-in clubs to a previous set built on the previous color code system, can the player order these on the old color code system to match?
    • Yes! PING will use the serial number to identify the specs of the set and will build the replacement/repair/fill-in clubs on the old color code system to match.
    • Even if the player was yellow or purple we can still replace or add clubs to that set, provided it was built on the old color code system.
  • How do I know which color code system a set of clubs was built on?
    • Using the serial number located on the hosel of the club we can quickly determine which color code system the clubs belong to.
    • Any clubs whose serial number starts with the letter ‘A’ were built on the new color code system; clubs with serial numbers not starting with ‘A’ were built on the previous system.
2017 ping chart changes2017 ping color code chart2017 ping dot colornew ping color code chartping dot colorping dot color chartping g400 color code chartping g400 dot color codeping g400 dot colorsping iron setping iron set dot colorping ironswhat do ping dot colors meanSours: https://blog.golfhq.com/what-do-ping-dot-colors-mean/

How to Understand Ping Golf Sizes

If you are in the market for Ping golf clubs, understanding the company's unique "Color Code" system will help you select the best set for your game. Ping's color codes refer to "lie angle," which is the angle between the club's shaft and the sole in relation to its length, according to Ping.com. For shaft sizes, Ping uses a static wrist-to-floor measurement to determine your ideal length. Ping uses its "5 Step Fitting Process" and a detailed questionnaire that incorporates your physical characteristics and limitations, handicap, frequency of play, current equipment, and other essential details into a formula for a proper fitting.

Step 1

Go to the Ping website, select the "Custom Fitting" tab on the menu, click on "Download Color Chart PDF" and open it. Look along the top of the chart for your height measurement in inches; the chart goes from 4 feet, 10 inches to 5 feet at the shortest end and 6 foot-7 to 6-foot-9 at the tallest end. The bottom of the chart has height measurements in centimeters.

Step 2

Become familiar with Ping's 12 different color codes, which it uses to determine the ideal lie angle, which ranges from "upright" to "flat" for irons. Note that "upright" codes are commonly for taller golfers and "flat" codes are commonly for shorter golfers.

Step 3

Look along the left side of the Ping color code chart for wrist-to-floor measurements in inches; the chart goes from 29 to 40 inches. Look along the right side of the chart for measurements in centimeters.

Step 4

Look at the colored stripes going horizontally across the chart at a slight angle up to the right. Note that this angle incorporates the taller end of the spectrum on the right side of the chart. Look down the chart, following the wrist-to-floor measurements, and note that the colors go from being labeled "upright" to "flat" to incorporate shorter wrist-to-floor measurements.

Step 5

Look at the maroon, silver, white, green, yellow and blue stripes, which are "upright," and range from the most upright at 4.5 degrees to the least upright at .75 degrees. Note the black stripe, which is considered the "standard" lie angle, dividing "upright" from "flat." Look at the red, purple, orange, brown and gold stripes, which are "flat," and range from the flattest at 3.75 degrees to the least flat at .75 degrees.

Step 6

Find your height on the chart. Find your wrist-to-floor measurement on the chart. Follow these two columns until they intersect. Note the dominant color in the square on the chart where your height column and wrist-to-floor column intersect to find your Ping color code.

Step 7

Determine whether the ball flight for your iron shots is typically a fade, slice, hook or draw. Reduce your fade or slice by choosing a more upright color code, and reduce your hook or draw by selecting a flatter color code, according to the Ping website.

Step 8

Understand that Ping uses your height and wrist-to-floor measurement to determine the shaft length for your iron fitting. Remember that the taller you are, the longer your shafts should be, and the shorter you are, the shorter your shafts should be.

Sours: https://golftips.golfweek.usatoday.com/understand-ping-golf-sizes-20502.html

Length ping chart shaft

Yes, even a bicycle. I laughed. In this madhouse, no one noticed how a black limousine drove up and a certain gentleman in an expensive suit got out of.

2017 Color Code Chart - US Version

As possible and delaying the moment of touching the culminating subject of our execution - her wet, tender pink pussy. When I finished with my stomach, I grabbed her under the thighs and laid her on her back. She put her legs on my shoulders and opened her tender holes for me. Pink anus groove is the favorite in this game.

Similar news:

At about eleven in the evening they sent me to bed and, falling asleep, I heard the echoes of the holiday for a long time. The guests decided to stay. There weren't enough sleeping places for everyone. Elizabeth had to give up her room and she lay down with me.



1934 1935 1936 1937 1938