Ethiopian Naming Conventions, Rolling Butcher Block Island Ikea, Table Top Heater Lowe's, Skiff Controls Xbox, Online Brainstorming Tools,
Rug tufting is a unique art in that you can create enormous works with relatively few materials. Once youve invested in a good tufting gun, youve got nearly everything you need to start tufting!
The problem is, choosing the right tufting gun is difficult. Amazon and other retailers are filled with cheap knock-off tufting guns that break down after your first few rugs.
To help you choose the right tufting gun for you, I put together this comprehensive buyers guide. First well cover a few key details you need to know, then well have a look at the best tufting guns, where to buy, and more.
If youre just looking for a quick recommendation, check out any of the models listed below. They wont do you wrong!
Affiliate disclosure: Articles on Tiny Workshops may contain affiliate links.
Best tufting guns: Quick picks
AK-I Cut Pile Tufting Gun
- Perfect cut pile tufting gun for beginners
- Lightweight, durable, and easy to use
- Buy just the tufting machine or a full kit with supplies
AK-II Loop Pile Tufting Gun
- Loop pile version of the tufting gun above
- Lightweight, durable, and easy to use
- Buy just the tufting machine or a full kit with supplies
KRD-I Cut and Loop Pile Tufting Gun
- Can switch between cut and loop pile settings
- Requires some expertise to use and set up
- Not ideal for beginners
What is a tufting gun?
A tufting gun is a handheld tufting machine used to make rugs. Its much faster than manual methods like latch hook or punch needle, but a step down from industrial tufting machines for carpet.
Tufting guns have a lot of advantages over other rug making or weaving techniques. As mentioned above, theyre very fast. A medium-sized rug can be knocked out in a few hours.
Theyre also relatively affordable. A few hundreds dollars will get you a solid machine, and the only supplies you need are yarn, backing material, and creativity.
Rug tufting has been around for decades, but its come back into style recently thanks to social media platforms like TikTok. And Im all for it!
How does it work?
Tufting guns work very much like a sewing machine. It has a foot that rests against the backing material, then a large needle pushes yarn through the material, leaving some on the other side.
Depending on the type of tufting gun you have (or the settings), it will either leave a loop (loop pile) or a strand (cut pile) on the other side. More on that in the section below.
One very important thing to keep in mind is that you can run more than one thread of yarn through the tufting gun at a time. Use creative combinations to make interesting patterns, or just save time by pushing through more threads at once!
Loop pile vs cut pile tufting guns
The biggest decision you need to make before buying a tufting gun is whether or not you want a loop pile or cut pile model. There are some models that can do both (learn more about that below), but they tend to be more expensive and fairly difficult to adjust back and forth.
For beginners though, you should absolutely stick to a simple model.
So how do you know which one to choose? Well, there isnt really a right answer here.
Both loop pile and cut pile tufting guns are great fun, and both can be used to create incredible pieces. Which one you choose will largely be personal preference.
For me personally, Id probably lean toward cut pile because I like the feel of the finished rug, but again, thats just personal preference.
Get inspired with the latest Tiny Workshops tours and interviews!
Best tufting guns
With all that background info out of the way, we can finally get to the main show: which tufting guns to buy and where to buy them!
Youll find a lot of junk models (especially on Amazon), but Ive selected four of the best tufting guns that are reliable and easy to use for both beginners and experts alike.
Note that all of the shops linked below sell both the tufting gun separately or a full kit with other tufting supplies. Tuft the World also sells an excellent starter kit, and you can save 15% with the code TINY at checkout!
1. AK-I Cut Pile Tufting Gun
For beginner tufters, the AK-I is the best tufting gun there is. Its limited to cut pile tufting, but it remains a popular option because of just how easy it is to use.
This thing is easy to set up and hard to break, both of which are extremely common problems when tufting. Plus, it weighs just 3lbs (kg), whereas other models can weigh five times that. Its great for long tufting sessions.
The main problem with this model is availability. Most shops take pre-orders, and it can take 3+ months to ship. Thats a long time to wait for a new hobby.
Thankfully, the shop listed below seems to maintain stock. Its based in New Zealand, but they use express air delivery so you can expect your machine in less than two weeks, no matter where to live.
To make matters better, they offer a variety tufting gun kits, as well. You can get your AK-I cut pile tufting gun with a frame, primary tufting fabric, yarn, or even a second loop-pile tufting machine (the AK-II, listed below).
Another place to buy the AK-I tufting gun is a specialty shop called Tuft the World. They have a variety of tufting supplies on offer, and you can save 15% on your purchase at checkout with the code TINY.
2. AK-II Loop Pile Tufting Gun
Next up is another tufting machine from the same manufacturer, but this time its aimed at loop-pile tufting.
All of the benefits of the model above still apply here: its lightweight, durable, and easy to set up. The only difference between the two is the type of rugs they can create.
However, it also suffers from the same big downside. It can be very difficult to get your hands on, and most shops deliver months after purchase.
Again though, the same New Zealand-based shop mentioned above offers great pricing and shipping times of just over a week. You may be able to find one a bit cheaper, but you wont find one thats more convenient! The same kits and bundles are available here, too.
If its sold out there, you can also buy this model from Tuft the World. Availability is a bit more limited, but you can still save 15% with the code TINY at checkout.
3. KRD-I Cut and Loop Pile Tufting Gun
If you absolutely must have a tufting gun thats capable of both cut pile and loop pile tufting, the KRD-I is one of the best around.
Featuring an improved design over its predecessor the KD-II, this is an industrial grade tufting machine. It supports both V and V power, with a handy speed control knob to slow it all down when you need to.
However, this isnt a tufting machine for beginners. Swapping between modes requires some expertise, so its best left for intermediate or advanced tufters who know their way around a basic machine.
Like this other models on the list, you can buy this one on Etsy at the link below, or at Tuft the World when its in stock. Remember to use the code TINY to save 15%!
4. AK-III Pneumatic Combo Tufting Machine
Ok, so youre a relative beginner but you still insist on getting a tufting gun capable of both cut and loop pile tufting?
Well, the AK-III is the model for you.
It has many of the same great design elements of the AK-I and AK-II above, but comes with extra parts and features that make it a combo tufting gun.
Although this model is relatively easy to use, there is one big caveat. This is an industrial-grade pneumatic tufting gun, so to use it youll need some kind of compressed air system.
That alone will likely add to your setup costs enormously, and the tufting gun itself is one of the priciest on the market.
Still, it can be a great investment for the truly dedicated tufter with a large budget. Buy it on Etsy at the link below, or from Tuft the World with the discount code TINY.
5. ZQ-II Cut and Loop Pile Tufting Gun
By last pick for the best tufting guns is the ZQ-II. Its the older version of the KRD-I listed above, but its still a very capable machine.
Again, its capable of both cut pile and loop pile work, but its considerably heavier and more finicky to set up than the other models on the list.
That said, if you know someone who can show you the ropes, youll be tufting away in no time. You also dont need to invest in an air compression system, which is great for small or residential workspaces.
Learn more at the link below, but be aware that supplies are limited to it may be sold out soon!
Other tufting supplies
Unless you buy a full tufting starter kit from one of the links above, youll need a few more tufting supplies before you can get started.
Learn more:Essential rug tufting supplies for beginners
Ive listed the basics below, as well as a few cheaper alternatives for those on a budget.
The first and most obvious tufting supply youll need is yarn. And lots of it.
The good news here is that just about any yarn is suitable for rug making. However, each one will yield different results, so its best to experiment before starting your final piece.
Natural wool, synthetic fibers, and even metallic and conductive yarns will work. That said, most people tend to stick to natural wool for that soft, smooth finish.
Perhaps the most important thing when buying is to buy yarn that comes wrapped around a cardboard cone. These feed into your tufting gun much more smoothly and prevent any snags while youre working.
This Etsy shop has a particularly great selection, and ships from Canada. Tuft the World also has some nice (but slightly pricier) yarn options, but you can save 15% with the code TINY at checkout.
You can also, of course, wrap any yarn around an empty cardboard cone if you have one handy.
Another absolute essential is backing cloth. This is the cloth that youll use the tufting gun on, and quality here really matters when it comes to the longevity of your rugs.
The absolute best material is primary tufting cloth. This tough, lightweight material is made for tufting, and even has grid lines printed on the fabric to help keep track of your designs.
Its also readily available to buy online. You can get it on Amazon, but I prefer buying from Etsy to support small businesses. Tuft the World also carries it in two different colors.
If you want to save a bit of money, you can also try burlap, monks cloth, or linen. These are significantly cheaper, but are more prone to ripping or tearing, especially for beginners.
Still, theyre a good option for practice pieces or quick rugs on the cheap! You can buy those fabrics just about anywhere.
Most tufting supplies will need to be bought, but one thing that can be easily DIYd is a frame. This essential component is where youll stretch your backing cloth for tufting.
As such, size is an important consideration. If you just want to make small rugs, a smaller frame will do. But for large, centerpiece rugs, youll need a huge frame.
The easiest way to make one of these is to slap together some 2x4s, add some large, sturdy legs, and round the frame with carpet tack strips. Heres a build video with more details.
All of these supplies are readily available at your local box store, but you can also buy a frame if youre really limited on time.
If dont want your rugs to fall apart the moment theyre finished, youll need to invest in a high-quality latex adhesive.
This is often the final step of rug making, but it pays to have your adhesive ready ahead of time. And you will need a lot of adhesive.
Id recommend a large tub of latex adhesive like this one. How much you buy will depend on the size of your rugs (and how prolific you are with your tufting gun), but its sold in four sizes so you can find the right one for you.
Simply use a paintbrush to brush the back of the rug with the adhesive, folding over the edges. When it dries, it remains flexible so it wont crumble, and provides a perfect anti-slip backing for any surface.
PVC and vinyl backing materials are also decent options, but these tend to be harder and heavier. Stick with latex glues to avoid the hassle.
You may also be able to find this kind of glue in big box stores or local specialty shops. Just make sure its the right kind for rugs.
A few other tools you may need in your rug making journey are a trimmer to finish your cut-pile rugs, white mineral oil for lubrication, tweezers, thread snips, and a large drop cloth to protect your floors from damage.
Some tufters also use a projector to enlarge their designs before starting to tuft, but you can also use a simple grid to get accurate results. Remember, you can always use the tweezers to pull out any erroneous threads!
Where can I buy a cheap tufting gun?
There are some inexpensive tufting guns on Amazon and other retailers, but I wouldnt recommend them. They tend to break down frequently. A better bet is to ask around local craft groups (or online communities) to pick up a second-hand tufting machine.
How do I change the speed of my tufting gun?
Depending on the model, there may be a knob at the base of the handle to adjust speed. Oher models support both V and V power, so swapping to a regular outlet may slow the speed.
What kind of oil should I use to lubricate my tufting gun?
You should lubricate your tufting gun before every use, and the best option for this is white mineral oil. This wont gum up your machine, and its even sold with a handy telescoping spout as sewing machine oil.
Thats all for this tufting gun buyers guide! Which machine will you be getting to start your tufting journey? Let everyone know in the comments below!
Note: Featured image credit: KnowledgeBySean
This entry was posted in:Reviews
Tagged with:art, crafts, diy, fiber art, rug making, tuftingSours: https://tinyworkshops.com/tufting-gun-buyers-guide/
Introduction: Rug Tufting
About four months ago from one day to another all Youtube suggested to me were rug tufting videos. So I started to watch a few and was obsessed ever since.
Over the years I have started quite a few different hobbies (like 3D printing, woodworking, embroidery, modifying Nerf blasters) and I can tell you rug tufting is easily one of the most fulfilling. The great thing about it is that it's quite easy to learn and extremely versatile. I also love that what you make actually serves a purpose. You also don't need many things to get started. Though it is certainly not a very cheap hobby since the materials and tools add up.
Before you can get started you will have to make a few decisions:
- Would you like to use a punch needle or rug tufting gun
- Do you prefer a cut pile or a loop pile rug or would you like to make both
- What type of primary and secondary backing materials would you like to use
- What type of yarn would you like to use
- How would you like to finish your rug
In this instructable I am going to tell you what decisions I made and why. After we are ready to start, I will show you how I create and finish my rugs.
Step 1: Manual Vs. Automatic
One of the first decisions you will have to make is to decide whether you would like to manually make your rug with a punch needle or whether you would like to get a rug tufting gun.
Since I am way too impatient to tuft manually I decided to go with a rug tufting gun. If you can only afford a punch needle or prefer the manual process, most of what I write here should also help you.
The next decision you face is whether you should get a "cut pile" gun, a "loop pile" gun, or one that can do both (more expensive and heavier).
The machines create loops of yarn. They can either be left as they are to create a "loop pile" rug or automatically cut to create a "cut pile" rug. You can also of course create a rug that uses both stiles.
The next decision you will have to face is where to get the gun. If you would like to support a local maker (should you be from the USA), I suggest looking at Tim Eads's page (https://tuftinggun.com/) he sells everything you need to get started. The prices for the tufting guns start at $
A cheaper alternative is to get the gun directly from a Chinese vendor (e.g. from aliexpress.com *). I paid about $ for mine (including shipment), but they seem to have gotten a bit more expensive. So if you don't mind waiting (mine took a month to arrive), are not from the USA, or don't care about the risk that there is no support if anything is broken, I would say go for it. But remember that you might have to pay taxes depending on from where the gun is sent.
The gun I got (pictured above) is a cut pile machine that can tuft up to 18 mm (roughly 3/4 inch). There are also high pile versions that use pneumatic air (they need an air compressor to work, the one I got doesn't). They can tuft to a length of about 70 mm (about 2 3/4 inches).
Step 2: The Frame
After you've decided how to make your rugs it is time to build the frame. Building the frame is quite easy in terms of woodworking. All you need is a square. You can either cut the beams at a degree angle, use a tenon, a bracket or simply screw the pieces together as I have done (don't forget to predrill the holes to prevent cracking). So far mine has worked great and just screwing one beam to the other is certainly the easiest solution.
Make sure that the beams you get are straight (the cross-section of mine is 3 cm x cm). You might also want to think about adding some feet to your frame so it is not going to fall over. You can just lean it onto a wall, but make sure that there is enough space for the needle to move without it pinching the wall. You should also consider your working height. I clamp my frame to a table so that I can work upright, without having to bend down too much. Otherwise, it is going to get uncomfortable rather quickly.
You can build it however big you would like your rug to be. One thing you should consider is, in what size you can buy your backing material. In my case, the material is sold by the meter so making the inside of the frame exactly one meter would result in a lot of wasted fabric since you need about 3 cm around the border to hold it in place. That's why the inside of my small frame is 90 cm, it gives me enough space to clamp the fabric in place without wasting too much material.
After you have built your frame you will have to consider how you would like to attach your fabric to it. A common solution is to use a staple gun. I prefer to use dual-purpose carpet gripper rods, that can be reused however often you would like. You should be able to get them in your local hardware store (or on amazon.com *). Be careful not to hurt yourself on the nails that are sticking out.
In order to allow the yarn to move freely, you might also want to consider using a construction that helps guide it, as I have done (with eye hook screws). You don't really need one though and can place the yarn at your feet. But be careful to keep it away from the gears of the gun.
There is also the possibility to buy a frame building kit here.
Step 3: Backing Fabric
Another decision you will have to make is what backing material to use.
From what I've read online burlap, linen, and monks cloth are possible candidates for tufting. Most people I have seen have either used burlap or monks cloth. I have tried them both and prefer to use monks cloth, even though it is more expensive. I found it easier to attach to my frame and got better lines due to it being more even, but if you are on a budget I suggest going with burlap.
I ordered my monks cloth directly from China since it was ridiculously expensive in Germany. Apparently, some types of monks cloth don't work. So far I have been lucky, but I suggest getting a smaller quantity first and to test it out.
There are multiple offers on amazon.com for tufting cloths. You can check them out here *.
Step 4: Secondary Backing Fabric
There are many technics you can use to finish your rug.
Once you are done tufting, you will have to fold your primary tufting cloth over to the back and hold it in place somehow. It can be sewn or glued. Carpet edge binding tape can also be applied for a protected edge finish.
Afterward, you can use a secondary backing fabric to cover the back of your rug. There are many different ones you can use like for example felt. I use either a non-slip fabric, an anti-slip mat, or felt and attach it with spray adhesive.
Step 5: Picking the Yarn
There are many different types of yarns you can use. All types have their advantages and disadvantages. I listed a few (sorted by the alphabet). There are of course also blends and many more types (like Polyester or Polypropylene). These are the ones I have tested:
Acrylic: Acrylic is is resistant to dirt, mildew, moths, and fading. Acrylic is more affordable than wool and is available in a wide range of colors. Sadly it has a tendency to fuzz and shed and is very soft, therefore it doesn't hold its structure well. Rugs made from acrylic are best in areas that aren't subjected to too much wear.
Cotton: While cotton carpets are soft and comfortable to walk on, they're also susceptible to stains and matting.
Nylon: Nylon is known for being one of the strongest and most durable fibers. It's popularly chosen for its resistance to staining when treated, fading, mold growth, and heat. These characteristics make nylon carpet one of the easiest carpets to clean and maintain.
Wool: Wool is considered a premium fiber as it is resistant to crushing, extremely durable and fire-retardant. Sadly it is also way more expensive than the other choices. If properly cared for wool carpets can last for a long time.
Making a selection is not easy and depends a lot on the money you have available and what you want to do with the rug.
I didn't like the feel of the nylon rug at all, since it is rather hard. The color choices are also very limited and therefore I am surely not going to use it to make a big rug.
I found tufting cotton to be tricky since it kept on slipping over the scissors and therefore the strand didn't get cut properly. Even using multiple strands didn't help. They were all pushed upwards by the scissors and didn't get cut (apparently they were too smooth and therefore the scissors couldn't hold on to it). So if you are planning on using cotton, remember to buy really thick yarn and test it first before buying all the yarn you need. Personally, I didn't like to feel of the finished rug quite as much as the ones made from wool and acrylic.
So after I did some testing I was sure to either use acrylic or wool. They were both a pleasure to work with and I loved the feel of the finished rugs. I ended up using acrylic mainly because it is cheaper and I am still practicing. In the long run, I will probably switch to wool. If I were to make a rug for someone else or if you are planning on selling them, I would probably go with wool. Though I have seen plenty of people selling hand-tufted acrylic rugs.
Unless you are trying to tuft cotton, the thickness of the yarn doesn't really matter. To get a good and consistent tuft, it is important that there is enough yarn in your gun so that it does not slip out of it. You can archive that with thinner yarn by simply using multiple strands.
Step 6: Glue
Glue is used to hold the yarn in place and therefore hugely important. It is applied to the back of your carpet once you are done tufting.
There are different types of glues that you can try. Though I highly suggest going with synthetic rubber.
Latex: Latex has traditionally been used to hold the yarn in place. The biggest issue with latex is that it will break down and crumble over time. Read this article online illustrating this. It's important to use high-quality latex to slow or prevent it from breaking down.
Polyvinyl acetate: PVA glue is cheap, easy to get and non-toxic (you might know Elmer's glue). It can be used for wall pieces and throw pillows. The bond is not as strong as the other types of glue mentioned here and also very stiff.
Acrylate polymer - synthetic rubber: Acrylate polymers are used in most industrial carpet glues. When it comes to tufting, AAT seems to be the first choice, from what I have read. It is a carboxylated styrene-butadiene rubber latex. Sadly I was not able to test it, because I can't buy it in Germany. The advantage of synthetic rubber is that it sticks really well and doesn't degrade over time like the natural counterpart.
To choose the glue I would like to use, I tried three different brands. If you are from Europe they should be easy for you to get. I bought them on Amazon. The Pattex and baufan glues are extremely similar. They look and smell about the same and have a similar viscosity. I didn't like them quite as much as the SOUDAL glue, because they stayed tacky even after a week of dry time. They also got tacky once they got moist. So if you can get it, I suggest going with the SOUDAL glue.
You will need quite a lot of glue. I used about kg on my Pacman ghost rug which is about 70 cm x 70 cm. So don't bother buying the small cans, if your planning on making more than one rug.
Step 7: Other Things You Need
There are a few other things you need. In the pictures, you can see the things I am using. They are:
- Permanent marker: to draw your design onto the backing fabric
- Pliers: to pick out the yarn, if you made a mistake
- Scissors: to cut the yarn and the fabric
- Clippers: to get a nice finish (you can also use the scissors, but clippers will save you time); sheep shears works even faster
- Palette knife: to apply the glue
- Hot glue: to hold the folded over backing fabric in place
- Spray adhesive: to attach the secondary backing fabric
- Projector: to transfer your image
You will also need a paintbrush (or compressed air) and all-purpose oil for maintaining the gun
Step 8: Preparation
Before starting, I rewind the yarn, because it is cheaper for me to get it in balls instead of cones and I want to make sure that it unwinds smoothly. So far it was definitely worth the afford and I haven't had any problems with tangling yarn.
Next, you will have to add the backing fabric to your frame. Take the time to stretch your cloth as tightly as possible, but make sure not to tear it. I start with one side and move around the frame. Increasing the tension bit by bit. The big advantage of the monks cloth I use is that there are lines on it. This way you can make sure the fabric doesn't get distorted when you put tension on it.
Once the fabric is attached, you can transfer the image onto it. I use a very cheap projector to trace my design onto the fabric like this * one. You can of course just draw it on freehand.
When picking your design make sure that the level of detail isn't too high. While you can do a lot of clean-up and make the lines on your rug nearly perfect, remember that most rugs are made for use and once somebody steps on it or you vacuum it, the fibers might move. I make my rugs extremely dense and therefore haven't had huge issues with distorted designs, but it is something you should keep in mind.
For this instructable I originally wanted to make a QR-code that leads to my instructables site but decided to go with the instructable robot instead and am really happy I did. Seeing it makes me extremely happy. I decided not to tuft the antennas and not to add them later, because I thought that it wouldn't look good and I am happy with the decision.
Step 9: Threading the Gun
Start by threading your gun, as shown in the pictures. Go through the yarn holder on top of the gun first. Then use a bent wire to pull the yarn through the hole in the needle.
Depending of the thickness of the yarn, you should use multiple strands. I suggest going with at least two. I usually use two to four strands.
Step Tufting #1
Before moving on to your rug I suggest doing a few straight test lines. This way you can figure out the right technic, pressure and speed. You can adjust the speed by turning the knob that is at the bottom of the handle of the gun. Once you've mastered straight lines you can try doing curves. The best way I found to do them is to go in small burst and correcting the position of the gun throughout.
You can only tuft in the direction of the foot. The foot of the gun has to stay in contact with the fabric during tufting. Make sure to use enough pressure to hold it in place.
Time Eads made a great video on how to get started.
Step Tufting #2
I start by outlining the different areas and fill them in afterward.
The excess yarn can just be cut off. Don't worry if the back looks a bit messy, we are going to cover it later.
I like my rugs to be rather dense, therefore I place the rows of yarn right next to each other, but you don't have to. You can place them slightly apart. If you are unsure how close to each other you want to place them, just do a test piece, since how close you will have to place them also depends on how many strands of yarn you use and how thick the yarn is.
Step Fixing Mistakes
Fixing mistakes is really easy, just plug the yarn out. But be careful not to do this too often, otherwise, you might risk tearing your fabric.
Don't worry if your lines look messy at first. They can easily be fixed later. Just use your pliers to push the yarn around. If some strands are way off, you can just plug them out.
In the picture, you can see my process. The button on the left is finished, the button in the middle shows how it looks before the clean-up and the button on the right shows how it looks before the second color is used.
If you are having troubles with holes, rips, & tears, check out this awesome guide.
Step Gluing the Yarn in Place
Once you are happy with how your rug looks, it is time to hold the yarn in place. Like I have written before, I am using synthetic rubber to do so.
Apply the glue while stretched otherwise it might curl. I lay my frame on the floor and use a palette knife to apply the glue. Go over the sides by about 3 cm to prevent the monks cloth from fraying later on. Make sure that all the yarn is covered.
Let the glue dry for about 24 h before taking the rug down from your frame.
Once again, Tim Eads made a great video:
Like I have written at one of the steps before there are many different ways how you can finish your rug. Here I am showing you how I finish mine.
Once the glue is fully dried, I take the fabric off the frame and cut around the rug at a distance of about 3 cm.
Step Finishing the Rug
In order to be able to fold the excess fabric over to the back, you will have to cut into the border. Otherwise, you won't be able to follow the curves.
As you can see in the pictures, I apply a generous amount of hot glue on the border and fold it over. Be careful not to burn your fingers. I use the pallet knife to apply some pressure, till the hot glue cools off.
Once I am done, I trace the carped onto my secondary backing fabric and cut it to the correct size. Afterward, I use a spray adhesive to attach it. Make sure to use a lot of pressure in order for it to stay in place.
Step Maintaning the Gun
As you can see in the picture there is a lot of yarn build-up from tufting on the gun. In order for it to work properly, you will have to remove it. To do so, I use an air compressor, but you can also just use a brush.
After cleaning the gun you will have to lube it. All-purpose sewing machine oil works great. Just sparsely add it to all the parts where friction might build-up during usage.
Step Adjusting the Pile Height
You should start out by using the factory settings. Once you've got a feel for them you can adjust the tufting height.
Tim Eads from Tuft the World created awesome tutorials on how to adjust the pile height of your tufting guns. You can find them below. Which tutorial you will have to follow depends on the gun you have gotten.
Set the cut pile height:
Set the loop pile height:
Step Great Sources
Be the First to Share
Did you make this project? Share it with us!
Back to School: Student Design Challenge
3D Printed Student Design Challenge
She laid her head on my shoulder. It must have happened. - Now I felt only tenderness for Lerka, even though my penis was pressed against her stomach. I began to gently stroke her hair, but soon I found myself stroking her. Not as a sister, but as a woman.
Tufting gun reddit best
The screams of the victim seemed to only encourage the rapist as he worked at full power, inserting his long cock. Deep into her vagina. Julia has never had the experience of vaginal penetration of anything this huge before.Top 5 Best Electric Tufting Gun Review 2021
He was only four years older than me (I am 20 years old), and was of average height, but with an excellent inflated, beautiful body, like swimmers. The abs cubes were clearly visible on his stomach. And with every movement he could clearly notice the action of the muscles. For those who have forgotten, I will note that I am a thin blonde of medium height with a.
- Police jobs jacksonville fl
- Wicked ways lyrics
- Sudney 6d
- Topanga living cafe
- U verse 4k channels
- Property accounting manager salary
- Camtasia key and name
- Dremel multi max
- Woodlawn blue living room
Sergei was so dumbfounded by the picture that appeared to him that he did. Not immediately realize what had happened. Huge breasts looked at him with their big brown nipples, and a blouse and bra lay lonely on the floor.