Amcrest default ip

Amcrest default ip DEFAULT

Many times the users fail to customize the settings of Amcrest products like camera, doorbell, and sometimes lose the password or setting etc, so may need to Reset Amcrest camera to its default setting. Here Amcrest Support guides you, on how to reset Amcrest camera to default factory settings, and find out other issues related to Amcrest camera, which can arise the need to Reset Amcrest camera. Resetting the device can resolve issues most of the time, provided it is diagnosed that it is related to camera. At times, the issue could be with network and access application and resetting wont help in those cases. You can follow the troubleshooting guide to isolate the problem with camera and network and then proceed with Amcrest camera reset. If the device has issues with any specific feature and is not working properly, Amcrest camera factory reset can resolve the issues most of time.  It is highly recommended to delete your device from your Amcrest Smart Home account before performing a factory reset, so that you don’t have any issues while reconnecting the camera to App.

Reset Amcrest Camera: Battery operated cameras

amcrest customer service

Know this important information before you Reset Amcrest Camera. A factory reset is the option to revert your device settings back to its original factory default, when you are experiencing problems with the device. To factory reset Amcrest camera device, you have to find where is the reset button and for Amcrest it is on the back of your Smart Hub device. You will need a pin or paper clip or similar object to reset Amcrest camera. Please find below the general  information on how to factory reset Amcrest device.

Amcrest camera reset Steps begin here: To start the Amcrest reset process, delete your Amcrest device from the Amcrest Smart Home app.

To delete your device please follow the steps given below

  • You need to log into your Amcrest Smart Home app and select your device ( you want to reset) from the Devices menu. 
  • Now find and tap on the Settingsgears2.png ) icon. 
  • In the options given on next screen please tap on Delete Device
  • This is very important that, If you want to save your old or previous recordings, you must select or tap on “Keep Recordings“.
  • Now you need to tap on Delete and the device will be removed from the account settings.
  • Now lets move on to the smart hub device and locate the reset button on the back of your Smart Hub. It is a tiny hole on the left side of the power port.
  • Insert the pin, or similar device, into the reset hole and while pressing it hold the reset button for 45 seconds. The LED on the Smart Hub will flash indicating the device is resetting in process. Once the flashing stops, you are done with the hard reset and Amcrest camera Reset is complete. 
  • For any kind help for setup issues after camera reset, please speak with Support desk.


amcrest camera IP address

Amcrest camera Soft Reset Via Web Interface

To find Ip address of your camera: Customers access their Amcrest Camera via Pc, Laptop, or Mac computer by opening a mainstream web browser like Firefox, Google Chrome, Safari etc. Some customers get stuck with Ip address after reset. To locate the camera’s IP address, you need to download our free Amcrest IP Config Tool software. Click to Download button Windows Mac or go to After installing, find the IP address associated with the device you would like to view in the browser. Note down the IP address as you may need it for further setup or wifi settings.

Open the web browser (chrome safari etc) and enter this IP address into the browser. Press enter to access the web user interface.

Amcrest camera web access interface required in reset camera

In the web interface , enter the login credentials for your device. If this is often the primary time accessing the device, the username and password will both be admin. Click on Login.

How to reset Amcrest camera password :

If this is the first time logging into your device, you will be prompted to modify the password for your device. To modify the password, enter the new password you’d wish to use within the New Password field and ensure that the password used should be between 8 and 32 characters long with a combination of letters and numbers. Click OK and allow the stream to load. But at times, few of the steps given for resetting may vary according to your system and software and access device variables. On the Amcrest forum too, customers report for not being able to find the correct option according to their device interface. Still the process remain to access settings and perform Amcrest camera password reset through configuration settings. You can always talk to Amcrest support in case you find any difficulties while changing the camera password.

How to Reset to Default Settings

Note: Using the Restore to Default Settings button directly from the online interface of
your device won’t reset the admin password for your device. To reset the password, a
physical, hard factory reset will have to be performed and can vary from model to
Step 1: Log in to the web user interface (Web UI) for your device. For more information
on the way to access the online UI for your device, click here.
Step 2: In the web UI, navigate to, Setup>>System>>Default Settings>>Default Settings.
Step 3: Click on the Restore to Default Settings tab located within the Default Settings
Step 4: A prompt will appear asking if you are sure that you would like to proceed with
the factory reset. Click OK to start the reset.
A reset of your device will occur. You can log out of the web UI and log back in. The
settings for your device are going to be reset to its original factory default settings.

Reset Amcrest Camera or restore default settings for your amcrest camera, application screen options image

How To Perform A Factory Reset on Amcrest Camera- Reset Amcrest camera

A factory reset of the Indoor Pro HD IP Camera to its original system state by erasing all of the knowledge stored on the device in an effort to revive the device’s software to its original manufacturer settings. Sometimes the security cameras stop to connect to the web servers, it is the time to reset to the factory specs, provided the wifi is confirmed to be in good functionality.
Note: Before performing a physical, hard factory reset, it’s recommended to first perform a reset via the online interface (Web UI) of the camera on a computer. This is useful also if you are doing not have direct, physical access to your camera. For more
information on the way to perform a factory reset within the web UI of your camera,click here.

There is also an external factory reset button lit by a LED located on the backside of the camera. Press and hold the factory push button for about 20 seconds, or until the green light changes to red. Once the light turns red, the process will begin. This will ultimately restore the device to its factory settings and can reset all of the camera’s settings.

This will reverse the settings back to its day one when the system was turned on. All your custom settings and information will be deleted in the process. The factory reset will finish by panning and tilting the camera, ensuring operation and therefore the light will turn green and the camera then gets completely reset back to its factory state.

Image showing how to Locate Amcrest camera reset button on the back  to load Factory default settings. Amcrest camera factory reset guide

A hard reset of your Amcrest camera will catch on back to its original state by removing all the information stored on your device. It will restore the System to the innovative software of the device with the default factory settings. Your password will be reset to the Amcrest default password which is admin.


How to perform Amcrest camera factory reset with button on the camera itself

How to hard reset Amcrest camera: Before performing this reset method, you should complete the factory reset using the online interface. It is expected to unravel most of the issues you’re facing together with your Amcrest camera. This method can be useful if you cannot physically access your camera while preserving your other settings. The hard reset method requires you to possess physical access way to reset Amcrest camera from the reset button.

If you’ve got planned to perform a tough reset of your Amcrest camera, then locate the external factory push button at the backside of your Amcrest camera(as shown in the image above).

Here are the steps for Amcrest ip camera reset

  • Open the camera
  • Press and hold the reset button for 20 seconds
  • Now release the reset button one the led starts flashing
  • Wait for the camera to reboot as it takes few seconds for camera to load
  • Now you can create the password and camera reset is complete

Please note* The LED will light up the button when you hold it for 20 sec. It resets the Amcrest camera back to its original factory defaults. Be careful with this button in standard scenarios once you don’t want to reset your camera. In a problematic case, you would like to proceed with pressing this button for about 20 seconds for reset. You will notice a change in the light above the button which has now turned red from green. This shows that the reset process has started. Now this may completely restore your camera to its factory defaults.
The factory reset will finish once you notice the camera tilting side wise. The light above the reset button will once again turn green. After that, you’ll set your new password and username for your camera by accessing the web UI to form sure the security and privacy of your data.

Amcrest camera reset: Factory Reset ASH21 camera

ASH21 Factory reset differs only with the button on the camera and you need to locate that Reset button by sliding the camera upward, as shown in the image below. We recommended users to delete that particular camera/device from the Amcrest Smart Home account before doing a Amcrest factory reset. Please follow the below given instructions for ASH21 Amcrest camera factory reset.

  • To Locate Rest button to perform Factory Reset on Amcrest ASH21 Camera, Raise the camera upward a little and you will see the Amcrest camera reset button on the right side as shown in this image below.
Amcrest camera reset button on ASh21 camera
  • Once you have located the reset button, Now press and hold this factory reset button for 45 to 60 seconds and allow the camera to reset, it takes few minutes to complete the reset. While the camera completes the Amcrest factory reset process, the camera will rotate and the front LED of the camera will blink green, indicating the completion of process and is now ready to be connected back to the app.
  • Now you need to reconnect the camera via the App on your phone or tab. 

How to Perform a Factory Reset Amcrest Outdoor camera

When it comes to resetting the outdoor camera it may not be possible to reach the camera due to its location or position. Outdoor cameras are generally placed higher so you may not be able to access it every time. Always consider performing a physical or hard factory reset as the second option with soft reset being the first option. We strongly recommended to perform a Amcrest camera reset via the web user interface (Web UI) of the camera on a computer or even browser on you phone. This is useful when you do not have the direct or physical access to cameras. For more information on how to perform a factory reset in the web UI of your camera, See the steps below.

  • We need to log in to the web user interface (Web UI) for cameras.
  • In the web UI, now we need to navigate to, Setup option and then select System and select Default Settings.
  • One in default settings now in the mid of screen you will see two option, default settings and factory default, lets click on Factory Default.
  • Next, the prompt will appear for confirmation to proceed with the factory reset.
  • Now you need to enter the password for your camera and then click Save to start the reset. Wait for few seconds and reset will be complete.

To do Hard Reset for Amcrest outdoor Camera: You would need a screwdriver to open the camera hatch to access reset button. You check the camera manual to know if your camera has a reset button behind the hatch or it has a reset button on the motherboard, depending upon your camera model it will vary.

For reset button on the motherboard : To perform a hard factory reset of your device, you will need to open the camera and gain access to the camera’s motherboard. On the board there will be a small black button inside. Please press and hold the button for 45 seconds, then let it go. Please see this reference image that will help you locate the reset button.

reset button on the motherboard of amcrest outdoor camera

Amcrest outdoor camera reset button with hatch

  • First step is to locate the reset hatch on the top of the camera. Then using a Phillips head screwdriver, you will have to remove the 2 screws to open the hatch.
  •  Once the latch is open, you need to locate the reset button, which is generally next to the MicroSD slot on the camera.
  • To begin the process of reset, Press and hold the reset button for 30-45 seconds and allow the camera to reset.
  • Once the reset is complete place the reset hatch back onto the camera and secure it. The camera factory reset is done and it has been reverted to original factory settings, which also includes usernames, passwords along with other settings. The default username and password will be admin.
  • Set up and password and reconnect it to your network or Internet and you should be good to go.

How to Perform Amcrest Factory Reset For NVR

Sometimes, due to Amcrest NVR malfunction or issues with device features and performance, you may be left with the only option to reset Nvr to factory settings. To begin the physical factory reset process you will need to remove the top NVR cover. Use a Phillips head screwdriver to remove the screws securing the cover. Once the screws are removed, you need to lift the lid to see the NVR’s motherboard. On the NVR motherboard you will have to locate a small black button, which is the factory reset switch for your device.

Process for Amcrest NVR factory reset:

  • Remove the cover of the NVR, Remove the screws on side and bottom to remove the cover (refer to usr manual for your device model)
  • To factory reset NVR, you need to hold the reset button down and unplug the NVR from power.
  • Once power cable is disconnected from the unit, please continue holding the factory reset button for atleast 4 – 5 seconds, while you are holding the reset button, now plug the power supply back into the unit. ( you should be holding the button down when you reconnect power cable)
  • Now when power is reconnected, you should hear a beep sound , even if it is not giving beep sound thats alright and proceed. Continue holding the reset button and allow the device to initialize for 20 – 30 seconds and then release the button once the system finishes loading. 

For any issue after this reset or problems with reset speak to us for further diagnostics. Dial +1 530-455-9359 and talk to Amcrest support

Amcrest Camera Factory Reset Button Hold Time For Various Models

Check out this part and according to your device see the Reset button hold time for factory reset of your device. Speak with support, if cannot figure out for little more complicated reset procedure for your device.

For IP2M841 and V3 model: The reset button hold time is of 20 seconds

For ASh21: The reset button hold time is 45 seconds.

Amcrest IP2M-842/IPM-722 Bullet camera: The Reset button hold time is 30 seconds.

Factory Reset (IP4M-1051) PRo HD : The reset button hold time is of 20 seconds.

Factory Reset (IP4M-1054E): Press and hold the factory reset switch for 20 – 30 seconds and then release.

Factory Reset (IP4M-1026): For this device you need to open the cover and keep the POE cable connected. The RST button is the Reset button on this camera and hold time is of 30 seconds.

Factory Reset (IP4M-1024E): For this device you need to access the camera’s motherboard. Use a paperclip for touching the filaments together for at least 5 seconds and reset will start.

Factory Reset (IP4M-1048EW-AI): Hold the reset button for 30-45 seconds. However, holding it for more than 30 Seconds will initiate the Amcrest camera reset process.

Factory Reset (IP4M-1046EW-AI): Locate the factory reset switch on the motherboard of the camera. The factory reset switch is right next to the microSD card slot. The hold time for Resetting this Amcrest camera is 10 – 20 seconds and then allow the camera to reset. 

Factory Reset (IP4M-1026E): Unfasten and remove the top shield of the camera and then remove the top plastic covering around lens and IR and access motherboard. Locate the small factory reset switch on the motherboard, Press and hold for about 45 seconds and the camera will reset.

Factory Reset (IP4M-1055E): Remove the metal casing around the unit to access Amcrest camera reset switch on the mother board and also remove the lens cover on the eyeball portion of the camera to access it. Press and hold the factory reset switch for 45 seconds


Sometimes you don’t know your default password, default IP address, and how to access it. Below we will show you how to change these and restore default settings so that your Amcrest outdoor camera is safe from malicious access. 

In General, the default password for Amcrest is “admin” including the following other credentials

Username: admin
Password: admin
IP address:

Don’t know the username and password reset your Amcrest outdoor camera uses? Don’t worry; all you have to do is reset it to restore default settings. That’s not a problem if you can locate the Amcrest outdoor camera reset button.

To learn how to Reset to restore default settings, follow our guide below.

Amcrest Default Password Reset

Quick Navigation

In the Amcrest camera, the default password of a device requires a physical reset. This procedure varies from product to product but typically involves holding down a specific key combination and restarting the unit. 

The Default Password For Amcrest DVRs, NVRs, Or IP Cameras

Username: admin
Password: admin
IP address:

Default IP Address

You have to approach your Amcrest outdoor cameras through the web browser interface of your PC. Open the web browser and write the IP address of your Amcrest outdoor camera in the IP address URL bar. Login with the credentials of the Amcrest outdoor camera. (1, 2)

In the Live View screen of the Amcrest outdoor camera, click on the default factory settings button. It appears in the upper right corner. In the top menu, right-click on the network. Now click on TCP/IP. (3)

Make sure the mode is set to static. Verify that the Amcrest outdoor camera still has the original IP address, after press the Amcrest camera reset to the factory default factory settings from the Amcrest manufacturer? If you prefer to set the mode to DHCP, the IP address of your Amcrest surveillance pro software will now switch.

How To Change The Amcrest Hidden/Admin Password?

To change the password for your Amcrest surveillance pro software, log in to the Amcrest surveillance pro software with the default password and set it. You could also modify it with its setup tool. 

How To Obtain The Reset Amcrest Camera Default Password?

If you’re looking to reset your Amcrest surveillance pro software back to its default factory settings, there is an easy way. You can use the default password and username, which are both admins. 

Always perform a factory reset or a manual Amcrest surveillance pro software configuration; before resetting the Amcrest camera, remove your Amcrest surveillance pro from the network or perform a factory reset to return the camera to its original default factory settings. To reset your Amcrest surveillance pro software, you must have access to the motherboard via the Allen-wrench tool. You can get this tool directly from your camera kit or any electronic store.

The housing consists of the base, the top, and the left and right side pieces. To remove this housing, turn the base counterclockwise to release it, then pull it out to expose the base plate. To factory reset, first, use the Allen key removal wrench to pull the lens cap off the eyeball part of the Amcrest surveillance pro software. Next, use the Allen wrench tool to move the base plate switch from solid red to solid white.

Hold down the factory reset for approximately forty-five seconds to perform a factory reset. Note that after the Amcrest surveillance pro software completes the Amcrest camera factory reset process, the password and username will return to the default, namely admin.

Wrapping UP

Set your password to change default factory settings and view images. It would help if you changed it immediately, as the defaults are publicly available (the default password for Amcrest cameras is “admin”). The reset is very easy to perform and only takes a few seconds. It is also possible to find more information on the manufacturer’s website for the factory reset. The factory reset is a necessary process to find the initial settings. 

The default password or IP address of your Amcrest surveillance pro software may have been changed or reset by the previous owner. If you are uncomfortable changing the password or IP address, don’t hesitate to contact Amcrest Technical Support for assistance.

You can also visit to change the default login information for your Amcrest surveillance pro software or get the reset. Remember that you can log in at any time by accessing on a PC or mobile device.

(1) IP address –
(2) URL –
(3) TCP/IP –

  1. Used jeep virginia beach
  2. Smoky mountains weather
  3. Dangerous hunts 2009

Amcrest default password and IP address

In this article, you can find the Amcrest default password and learn how to change the default IP address in the first login. The process takes less than 5 minutes.

Amcrest Bullet Camera

The Amcrest camera comes with a default password

If you are trying to access your Amcrest camera for the first time and have no idea how to get it working, this article can help you with a step-by-step procedure.

The Amcrest default password and IP address

Default username:  admin

Default password: admin

Default IP address:

The camera used as an example in this article is the Amcrest IP4M-1046EW-AI

The information may be similar to other Amcrest models, but in any case, there's a way to get into the camera configuration using the Amcrest IP config tool.

Let's take a look at how to change the username and password for the camera.

The following diagram shows the Amcrest camera connected to a PoE switch.

Note the Default IP address that I will change to

Amcrest camera network diagram

In this example, I use a switch, but it could also be a router.

I'm assuming the Amcrest camera will not automatically get an IP from a local router (I don't have one in this example). Let's work with static IPs. 

The IPs in red represent the camera network range 192.168.1.x

The IPs in blue represent the laptop network range 192.168.0.x.

It's necessary to add an extra IP to the laptop (, so it can access the camera via its default IP ( and then change the camera IP to  a new one( I hope this makes sense... Please make you understand that.

==> If you changed the password and don't remember it, please watch the video in the end of this article for more information on how to reset it.

Add an extra IP to your laptop / computer

You can add an extra IP to your laptop so you can access the Amcrest camera.

Just follow the steps below.

  • Open the "Network & Internet Settings";
  • Click on the Ethernet icon;
  • Click on "Change adapter options";
  • Select "properties";
  • Select "Internet Protocol Version 4";
  • Click on "Advanced";
  • Click on "Add";
  • Add an extra IP address.

See the following picture for more details.

Right-click the network icon and click "Open Network Internet Settings".

Open Network and Internet Settings

Select "Ethernet," which represents your computer's interface.

Network settings

Click on "Change Adapter Options"

Winbdows Change Adapter Options

Click on "Properties"

Network Interface Properties

Click on "Internet Protocol Version 4"

Network IPv4

Click on "Advanced"

Advanced IP Settings

Click on "Add"

Add button

Add the IP address that is the same network range as the camera (192.168.1.x)

Extra IP

Use the Amcrest IP config tool

Now you can use the Amcrest IP config tool to change the camera's IP address.

Open the software and wait for it to find the IP camera.

Amcrest IP Config found the camera

Click on "Login"

Login with the default username and password  admin/admin

Amcres IP Config Login

On the "NET" tab, uncheck the DHCP box.

Change the camera's IP address.

Click the "Save" button.

Change the Amcrest Camera IP Address

Open a web browser and type the camera's IP address.

Login with the default username and password admin/admin

Change the password (mandatory).

Login and change the password

And it's done. Now you have your Amcrest camera using a new IP and password.

Video: How to reset the Amcrest camera

If you changed the default camera password but don't remember it anymore, it's necessary to reset the camera to factory default. Here's a video on how to do that.

Now you know how the Amcrest default password and IP addres and how  to change the them if necessary, you can use this procedure for different models.

If you need extra help, please visit the Amcrest Website.


This guide shows the Amcrest default password, the Amcrest camera default IP address, and how to modify them. The process is quite simple and just takes a few minutes to complete.

There are various Amcrest models of DVRs and NVRs on the market that use different default usernames and passwords. Actually, the latest Amcrest recorders don’t come with a password, you create one once you run the recorder for the first time. Below we’ve listed the default accounts and the passwords for Amcrest DVR or NVR. Below we’ve listed the default accounts and the passwords for Amcrest DVR or NVR.

Amcrest default password

The default username and password for Amcrest DVR/NVR and IP cameras are “admin” for both. However, Amcrest recorders come with various types of accounts (admin, guest, user). Check the list below and try them out in your recorder or standalone IP camera.

  • username: admin and password: admin (Type of the account: Master User)
  • username: admin and password: 888888 (Type of the account: Administrator)
  • username: admin and password: 666666 (Type of the account: Guest user)
  • username: default and password: default (Type of the account: Hidden)

Only the admin account works via the web browser and the rest work only when typed directly on the recorder. For example, the account “888888” doesn’t work on the web interface but works locally.

Also, the Amcrest IP cameras use only the admin account (the reset of the accounts listed above are applicable to recorders only).

The default password for the latest Amcrest DVRs/NVRs and IP cameras

The new generation of Amcrest DVRs and NVRs are shipped out without any password or as they call the recorders are “inactive”. The end-user or the installer has to initialize and create a new password once the recorder runs up for the first time.
Amcrest Default PasswordDuring the Startup Wizard, you will be able to set up the Admin Password (The default Username for the Administrator Account is “admin”). Make sure to select a strong password that meets the requirements of your system.

On some versions, on the Login Setup screen, you also will be required to enter a recovery email to be used in case you lose or forget your password. Also, you can set up security questions to recover your password.

Amcrest Default IP Address

Amcrest’s default IP address is All the IP cameras, NVRs, DVRs come with this IP address. Obviously, you need to modify the IP address of the camera and match it with your own network.

We will demonstrate easily how to change the default IP address of the camera. So, we have a camera and this camera is connected to a PoE switch, the laptop is getting the internet from the same switch (or router where this switch is connected to). For illustration, check the picture below.

Amcrest Default Password

As you can see the camera is connected to the PoE switch (or router) and the laptop/computer is getting the internet from the same switch/router.

Change Amcrest’s camera IP address

To change the default IP address you need to use Amcrest’s IP config tool which is the same as the Dahua configuration tool and can be downloaded here. Once it’s downloaded to your laptop, install it and then run the software.

Basically, this tool will scan the local network and list any IP cameras, DVRs, NVRs found on the network. In our case, we see a few devices there, find the one that is a camera (camera icon and the IP address

Select it and click Login (or double click), type the camera’s default username and password. Once you do that, you should see the next window which is shown below. From there you can modify the IP address of the camera, subnet mask, and gateway.

Amcrest Default Password

Match the IP format of your network. If your router’s IP address is then the camera’s IP address should be modified to (where xxx is a random number from 2 to 254). If your router’s address is then you can change the camera’s IP address to

To change the Amcrest’s camera password, just log in to the camera via the web browser using the default password and then modify it to the account section. Additionally, you can change it via the configuration tool as well.


Following the guide above you can change the default password or IP address of Amcrest cameras. Never use the default password, always change it and make sure to use a strong one (combination of letters, numbers, and special characters). If you’re stuck, contact Amcrest (or the seller) for technical support.

Disclosure:Some of the links in this post are Amazon affiliate links. This means if you click on the link and purchase any item, we will receive an affiliate commission at no extra cost to you. Thanks for your support!


Default ip amcrest

It's impossible. You promised. Everything is very simple. You will be with me now.

Amcrest Surveillance Pro Installation \u0026 Key Features Walk-through Tutorial

Denis today at 01:03 I dont understand you and specifically you, what do you think, what should I think about, if youre not talking about anything in particular. Margot today at 01: 04Denis today at 01: 04ha. but what about what happens before bed.

Similar news:

Why. Well, dont, okay. But why. You are so beautiful, I want to see you.

5165 5166 5167 5168 5169