Walbro marine fuel pump

Walbro marine fuel pump DEFAULT

For many decades, Walbro has made the 2000 Series and 6000 Series fuel pumps.   Those pumps were sold with names such as Dupree, Autopluse, AC, Stewart Warner, and Walbro.   Those pumps supplied fuel to countless vehicles, boats, stoves, etc. in the past 50 years or so.  

Well, the time has come to retire those fuel pump lines.   Today's technologies enable Walbro to offer a new design that flows better, requires less current, and doesn't require periodic replacement of a bellows.

NOTE:
Folks looking for a 6V version of the FR Series pumps need to send e-mail to Walbro's Engine Management Group. Ask them very nicely to pull the 6V version of the FR Series pumps off the back burner and make it happen.

STANDARD FEATURES- ALL MODELS

  • Current requirement: < 2 amps average
  • Reverse polarity protected up to 60 minutes
  • Dry run to four (4) hours
  • Compatible with all commercially available pump grade gasoline, gasohol. diesel or bio-diesel
  • Operating temperature: -40 ~ +70C (-40 ~ +155F)
  • Transient voltage protected to 100 volts
  • U.S. Coast Guard 16623-1 and 16623-2 approved
  • European CE Standards EN 61000-6-2 and EN 6-3-2100 approved

.

Click here for dimensions of these pumps.

FRA fuel pumps

This pump can be used in many applications that would have previously used the 2000 Series Bellows pumps [e.g 2401, 2402, 2402IP, 2403].   This pump will work great in applications that don't require high fuel pressure or flow rates [e.g. antique cars and small-engine vehicles].

  • Flow: to 190 lph (52 gph)
  • Self priming (dry lift) up to 24 inches
  • Continuous duty life (diesel fuel): >5000 hrs
  • Weight: 0.74 kg (1.63 lbs)
  • Inlet/Outlet ports are 1/8-27 NPSF

Unlike the 240x pumps, these are continuous-duty pumps.   They will not slow down/stop at a set pressure; they will run whenever power is applied.   DO NOT use these pumps for small stoves. Use an FRD pump [below]

 

Part Number Pump Price
FRA-1
(a.k.a.
FRA-1-1)
12V, 20 gal/hr, 4.5-7.0 psi, continuous-duty, w/ two 5/16 hose barb fittings [replaces 2401]$120.00
FRA-2
(a.k.a.
FRA-2-1)
12V, 16 gal/hr, 2.5-4.5 psi, continuous-duty, w/ two 5/16 hose barb fittings [replaces 2402]$120.00
FRA-4
(a.k.a.
FRA-4-1)
12V, 32 gal/hr, 8.0-13.0 psi, continuous-duty, w/ two 5/16 hose barb fittings$125.00
FRA-12
12V, 32 gal/hr, 10 psi
Look at FRA-4 for similar performance
Not available in aftermarket
FRA-13
(a.k.a.
FRA-13-1)
12V, 50 gal/hr, 12.5-16.5 psi, continuous-duty
Basically an FRC-10 without the inlet bowl
$135.00

FRD fuel pumps

The FRD fuel pumps are an intermitent, pump-on-demand pump like the old 2000 Series bellows pumps [e.g. 2401, 2402, 2403]. &nbsp
  • Flow: to 210 lph (55 gph)
  • Self priming (dry lift) up to 24 inches
  • Ampere hours: up to 70% less than FRA & FRC
  • Continuous duty life (diesel fuel): >10000 hrs
  • Weight: 0.75 kg (1.65 lbs)
  • Pump cycles only when fuel is demanded

 

Part Number Pump Price
FRD-1
(a.k.a.
FRD-1-1)
12V, 20 gal/hr, 4.5-7.0 psi, demand pump, w/ two 5/16 hose barb fittings [replaces 2401]$125.00
FRD-2
(a.k.a.
FRD-2-1)
12V, 10 gal/hr, 2.0-3.5 psi, demand pump, w/ two 5/16 hose barb fittings [replaces 2402]$135.00

.

Click here for dimensions of these pumps.

FRB fuel pumps

  • Flow: to 225 lph (60 gph)
  • Self priming (dry lift) up to 48 inches (120 w/ check valve)
  • Ampere hours: up to 70% less than FRA & FRC
  • Continuous duty life (diesel fuel): >18000 hrs
  • Weight: 0.83 kg (1.83 lbs)
  • Pump cycles only when fuel is demanded
  • Replaceable filter
  • Inlet/Outlet ports are 1/4-18 NPSF
  • 96 hour salt spray test (ASTM B-117)
Part Number Pump Price
FRB-2
(a.k.a.
FRB-2-1)
24V, 43 gal/hr, 8-11 psi pump, w/ two 5/16 hose barb fittings [replaces 6067]$160.00
FRB-4
(a.k.a.
FRB-4-2)
12V, 45 gal/hr, 8 psi pump [replaces 6150 and 6151]$160.00
FRB-5
(a.k.a.
FRB-5-1)
12V, 45 gal/hr, 8-11 psi pump, w/ two 5/16 hose barb fittings [replaces 6065]$155.00
FRB-6
Same pump as FRB-5, but different wire connector Not available in aftermarket
FRB-11
(a.k.a.
FRB-11-1)
12V, 43 gal/hr 6-8 psi pump, w/ two 5/16 hose barb fittings [replaces 6132]$160.00
FRB-25
Fuel pump for New Holland Canada
Same pump as FRB-5
Not available in aftermarket

Certain FRB models have been certified for marine use.   They have the following characteristics:

  • 1000 hour salt spray test (ASTM B-117)
Part Number Pump Price
FRB-13
(a.k.a.
FRB-13-2)
12V, 43 gal/hr 6-8 psi Marine pump [replaces 6802]$135.00
FRB-15
(a.k.a.
FRB-15-2)
24V, 34 gal/hr 6-8 psi Marine pump
Mil Spec, single-connector wiring
$135.00
FRB-16
(a.k.a.
FRB-16-2)
24V, 43 gal/hr 6-8 psi Marine pump [replaces 6803]$155.00
FRB-17
(a.k.a.
FRB-17-2)
24V, 34 gal/hr 6-8 psi Marine pump with Packard Electic wiring connector $135.00
FRB-20
(a.k.a.
FRB-20-2)
12V, 33 gal/hr 2-4 psi Marine pump [replaces 6805]$155.00
FRB-22
(a.k.a.
FRB-22-2)
12V, 43 gal/hr, 8-11 psi Marine pump $155.00
FRB-23
(a.k.a.
FRB-23-2)
24V, 43 gal/hr, 8-11 psi Marine pump $155.00

FRC fuel pumps

  • Flow: to 210 lph (55 gph)
  • Self priming (dry lift) up to 48 inches
  • Continuous duty life (diesel fuel): >10000 hrs
  • Weight: 0.83 kg (1.83 lbs)
  • Pump cycles continuously when power is on
  • Replaceable filter
  • Replaceable filter

The FRC-8 was the first FRC pump produced because it is the pump used by all the refers on big-rig trailers.   This pump can lift fuel several feet and has a check valve to keep the pump primed.

Part Number Pump Price
FRC-6
(a.k.a.
FRC-6-1)
12V, 36 gal/hr, 4-6 psi pump w/ 1/4-18 NPSF fittings [included] $140.00
FRC-7
(a.k.a.
FRC-7-1)
12V, 36 gal/hr, 4-6 psi pump w/ 1/8-27 NPSF fittings [included]
same as FRC-6, but with 1/8-inch inlet/outlet
$135.00
FRC-8
(a.k.a.
FRC-8-2)
12V, 28 gal/hr, 9-12 psi pump w/ 1/8-27 NPSF inlet/outlet [replaces 6103]$135.00
FRC-10
(a.k.a.
FRC-10-1)
12V, 50 gal/hr, 12.5-16.5 psi pump w/ 1/4-18 NPSF fittings [included]$140.00

Accessories

.....

Part Number Pump Price
Straight-1/8 Straight 1/8-27 NPSF to 5/16 hose barb
$3.00
45-1/8 45-degree 1/8-27 NPSF to 5/16 hose barb
$13.50
90-1/8 90-degree 1/8-27 NPSF to 5/16 hose barb
$5.00
Check-1/8 Straight 1/8-27 NPSF to 5/16 hose barb with check valve
discontinued
Straight-1/4 Straight 1/4-18 NPSF to 5/16 hose barb
$9.00
45-1/4 45-degree 1/4-18 NPSF to 5/16 hose barb
$15.00
90-1/4 90-degree 1/4-18 NPSF to 5/16 hose barb
$7.00
Check-1/4 Straight 1/4-18 NPSF to 5/16 hose barb with check valve
$10.00
Screen 420 420 micron inlet screen kit for FRB/FRC
with o-rings
$4.50
Screen 70 70 micron inlet screen kit for FRB/FRC
with o-rings
$4.50
Regulator Inline adjustable fuel pressure regulator [1.75 to 5 psi] with two 5/16 hose barb fittings Discontinued

Please read our Policies

© copyright 1999-2021 Auto Performance Engineering


Sours: https://www.autoperformanceengineering.com/html/fr_pumps.html

Walbro FRB-13 Fuel Pump - Industrial & Marine

Due to COVID-19, the automotive industry as a whole, is experiencing material shortages. As a result, Walbro® /TI Automotive and our suppliers have limited our inventory.

OUT OF STOCK -  Available via backorder only or may have shipping delays due to availability.

SKUs containing: 

5CAGCA, GCL and TCA (i.e GCA308, 5CA400) 
TU (Tank Unit Assembly)
FR Series (Marine and Industrial)

*Notice of Non-Affiliation and Disclaimer
WalbroFuelPumps.com is not affiliated, or officially connected with Walbro® or TI Automotive®. The official websites for Walbro® and TI Automotive® can be found at  https://www.Walbro.com and https://www.tifluidsystems.com
The names Walbro® and TI Automotive® as well as related names, marks, emblems and images are registered trademarks of their respective owners.

All GSL series are in stock with ample quantities.

All International shipping has been suspended due to Covid-19 with the exception of Canada. We will reinstate international shipping as these restrictions are lifted.

Sours: https://walbrofuelpumps.com/frb-13.html
  1. Yellowstone new series
  2. Diy softball team gifts
  3. Fabric bin with handles

Walbro FR Series Reciprocating Fuel Pumps - Marine and Industrial

OPTION

FRA

FRB

FRC

FRD

     

12 volt

X

X

X

X

     

24 volt

X

X

X

X

     

Lead wires, connectors and electrical ground (see notes 1 & 2)

A, B, C

A

A, B, C

A

     

Output pressure: 20 kpa (3 psi)

X

X

X

X

     

Output pressure: 35 kpa (5 psi)

X

X

X

X

     

Output pressure: 50 kpa (7 psi)

X

X

X

X

     

Output pressure: 70 kpa (10 psi)

X

X

X

X

     

Output pressure: 90 kpa (13 psi)

X

X

X

X

     

Self priming (dry lift) of more than 305cm (120”) (see note 3)

X

X

X

X

     

Standard external finish (meets ASTM B-117 (96) hr salt spray)

X

X

X

X

     

Marine external finish (meets ASTM B-117 (1000) hr salt spray)

X

X

X

X

     

Bowl drain (see Figures 1 and 3)

 

X

X

      

Transparent fuel bowl- not USCG approved (see Figure 2)

 

X

X

      

Inlet filter: 70 micron

 

X

X

      

Inlet filter: 420 micron

 

X

X

      

Magnetic trap

 

X

X

      

Inlet fuel fitting thread- 1/8-27 NPSF

X

X

X

X

     

Inlet fuel fitting thread- 1/4-18 NPSF

 

X

X

      

Outlet fuel fitting thread- 1/8-27 NPSF

X

X

X

X

     

Outlet fuel fitting thread- 1/4-18 NPSF

X

X

X

X

     

Internal outlet check valve (available with 1/8-27 NPSF only)

X

X

X

X

     

External outlet check valve - 1/8-27 NPSF (see Figure 4)

X

X

X

X

     

External outlet check valve - 1/4-18 NPSF (see Figure 4)

X

X

X

X

     

Straight fuel fitting: 1/8-27 NPSF to 5/16 hose barb (see Figure 5)

X

X

X

X

     

Straight fuel fitting: 1/4-18 NPSF to 5/16 hose barb (see Figure 5)

X

X

X

X

     

45° fuel fitting: 1/8-27 NPSF to 5/16 hose barb (see Figure 6)

X

X

X

X

     

45° fuel fitting: 1/4-18 NPSF to 5/16 hose barb (see Figure 6)

X

X

X

X

     

90° fuel fitting: 1/8-27 NPSF to 5/16 hose barb (see Figure 7)

X

X

X

X

     

90° fuel fitting: 1/4-18 NPSF to 5/16 hose barb (see Figure 7)

X

X

X

X

     

Mounting (see “MOUNTING AND FITTING LOCATIONS AND DETAILS”)

F or G

F or G

F or G

F or G

     

Fitting location (see “MOUNTING AND FITTING LOCATIONS AND DETAILS”)

H, J

H, K

H, K

H, J

     
Sours: https://walbrofuelpumps.com/marine-industrial-fuel-pump

Walbro 6000 series pump

Walbro's Series 6000 pumps offer exceptional performance in a variety of demanding applications.   The are perfect for automotive, truck, off-highway, agriculture, RV, and military or industrial applications. These pumps can handle gasoline, diesel fuel and many other fluids.

Because Series 6000 pumps have only three moving parts, there is practically nothing to wear out.   Electronic circuitry, encased in epoxy to resisty shock and vibration, eliminates mechanical switching for exceptional reliability.   A magnetic filter traps metallic particles.   Two filters are offered: 70 micron for gasoline pumps or 420 micron for diesel pumps.   Filters are easily accessible for cleaning.

Series 6000 pumps are available in pressure ratings from 3 to 10 psi.   Military-approved models are available.   Series 6000 pumps are self-priming and have high lift capabilty.   The 10 psi version is particularly useful with high heads, long lines and high lifts.

The Series 6000 lineup includes three models which are widely used in truck refrigeration units throughout the world.   THese service replacement units are available in gasoline and diesel versions.

 

Part Number Pump Old Part Number Price
6132 12V, 7 psi, 43 gal/hr, negative ground, 1/4" NPSF orifice, w/ gasoline filter
flow graph
6013W discontinued
use FRB-11 pump
6131 12V, 5 psi, 36 gal/hr, negative ground, 1/4" NPSF orifice, w/ gasoline filter
flow graph
6001W discontinued
6146 12V, 5 psi, 36 gal/hr, negative ground, 1/8" NPSF orifice, w/ gasoline filter
flow graph
6018W discontinued
6065 12V, 10 psi, 45 gal/hr, negative ground, 1/4" NPSF orifice, w/ diesel filter
flow graph
6065W, 6136 discontinued

use FRB-5 pump
6067 24V, 10 psi, 43 gal/hr, negative ground, 1/4" NPSF orifice, w/ diesel filter
flow graph
6067W discontinued

use FRB-2 pump
6150 12V, 8 psi, 45 gal/hr, Gasoline, John Deere/Oshkosh Chassis, Chev 454 n/a discontinued

use FRB-4 pump
6151 12V, 8 psi, 45 gal/hr, Gasoline, John Deere Chassis, Ford 460 RE36566
RW24286
discontinued

use FRB-4 pump
6104 12V, 5 psi, 1/8" NPSF orifice, w/ gasoline filter 6104W discontinued
6103 12V, 10 psi, 1/8" NPSF orifice, w/ diesel filter 6103W discontinued
use FRC-8 pump

Walbro Marine Pumps

Walbro Marine Pump

Walbro marine electronic pumps are engineered to the strictest safety requirements.   They exceed the fire resistance, corrosion reistance and dielectric requirements of the Marine Division of Underwriters Laboratory.   They also meet the "Boat and Associated Equipment Safety Standards for Electrical and Gasoline Fuel Systems" published by the United States Coast Guard, January 31, 1977.

Walbro marine diesel electronic pumps provide dependable, pressure-controlled fuel supply.   They can pull or push fuel.   they are self priming, eliminate hand pumping, and reduce vapor lock problems.   They can be used as a completely independent fuel pump system, or as a booster or standby unit.   They can transfer diesel or gasoline.

Thanks to a solid state design, mechanical switching elements are eliminated for reliable operations.   Only three moving parts are incoporated in the pump, so there is little to wear out.   The electrical system is fully insulated and sealed, with a two-wire hookup and static ground connection.   Current draw is low.   Two filters are used.   A magnetic filter traps metallic particles while a microbon filter dissipates water and collects fine particles.

These pumps are labeled "Diesel Use Only," but they work great with gasoline, too.   The label is mainly there to protect the manufacturer - If your boat has a gasoline leak, your boat catchs fire, and you die, no one wants to get blamed for it.

 

Part Number Pump Old Part Number Price
6802 12V, 7 psi 43 gal/hr Marine pump, Neutral ground 1/4 NPSF female fittings
flow graph
6092 discontinued
use FRB-13 pump
6805 12V, 4 psi 33 gal/hr Marine pump, Neutral ground, 1/4 NPSF female fittings
flow graph
6095 discontinued
use FRB-20 pump
6803 24V, 7 psi 43 gal/hr Marine pump, Neutral ground 1/4 NPSF female fittings
flow graph
6093 discontinued
use FRB-16 pump
6806 24V, 4 psi 33 gal/hr Marine pump, Neutral ground 1/4 NPSF female fittings
flow graph
6096 discontinued

Parts and Accessories

You can purchase these parts online by adding them to your shopping cart. Click on "checkout" when you are done.

 

Part NumberCommentsPrice
300-1000 Replacement 420 micron [diesel] filter for non-marine Series 6000 pumps
[contains filter and cork gasket]
$5
plus shipping
300-1001 Replacement 70 micron [gasoline] filter for Series 6000 pumps
[contains filter and cork gasket]
$5
plus shipping
300-1009 Replacement 70 micron filter for Marine pump
[contains filter and o-ring seal]
$5
plus shipping

Please read our Policies

© copyright 1999-2021 Auto Performance Engineering


Sours: https://www.autoperformanceengineering.com/html/6000_pump.html

Pump fuel walbro marine

" - thought Masha and immediately pretended to be asleep again, as the guy began to go ashore. Again, through parted eyelids, she watched the guy come out and when his stomach appeared out of the water, with abs, and then groin, she. Wanted to turn away and close her eyes, but could not.

Walbro GSL392 fuel pump

Victor put his hands on both of her cheeks and then kissed her gently on the lips, feeling the taste of. His cum smeared across her face. "Sorry," he whispered.

Now discussing:

In 1957, my father got involved in some dark Cuban sugar scam. He invested all his capital in the business and burned out. We have remained beggars. Father shot himself. Pour some rum for me.



1313 1314 1315 1316 1317